This article mainly introduces:

India hydraulic cylinder,accumulator hydraulic cylinder manufacturer,accumulator hydraulic cylinder

(India accumulator hydraulic cylinder,produced by Hengyu Group）

accumulator hydraulic cylinder are widely used in India，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed accumulator hydraulic cylinder for customers from India.

Introduction to accumulator hydraulic cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

accumulator hydraulic cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

Classification of accumulator hydraulic cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

The accumulator hydraulic cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure accumulator hydraulic cylinder can use 20 steel pipe, and the high pressure accumulator hydraulic cylinder can use 45 steel pipe.

Answers to some questions about accumulator hydraulic cylinder:

How to deal with oil cylinder leakage?
The causes of oil leakage and treatment methods are as follows: (1) The spool is stuck or the valve hole is blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check valve body for wear. (2) The piston rod and cylinder are stuck or the hydraulic cylinder is blocked. At this time, no matter how to operate, the hydraulic cylinder does not move or moves very little. At this time, it should be checked whether the piston and piston rod seal is too tight, whether it enters the dirt and colloid precipitate: whether the shaft line of the piston rod and the cylinder is in alignment, and whether the wearing parts and seals are invalid.

What is a constant velocity cylinder? What is the difference between hydraulic cylinder and constant velocity cylinder?
The constant speed cylinder should be the same as the speed of the piston rod extension and withdrawal cylinder is called the constant speed cylinder. The difference between it and the ordinary hydraulic cylinder is that the ordinary hydraulic cylinder only has a piston rod extended out, and the general extension speed is slow and the recovery speed is fast, because of the relationship between the effective area. Effective area of piston chamber > Effective area of piston rod chamber. The effective area on both sides of the constant speed cylinder is the same, because there are piston rods sticking out at both ends. The application of constant speed cylinder is most common in grinding machines.