This article mainly introduces:

Germany hydraulic cylinder,road paving machine hydraulic cylinder manufacturer,road paving machine hydraulic cylinder

(Germany road paving machine hydraulic cylinder,produced by Hebei Hengyu company）

road paving machine hydraulic cylinder are widely used in Germany，because of clever hydraulic energy conversion，excellent temperature resistance，simple structure and reliable operation.So our company has designed road paving machine hydraulic cylinder for customers from Germany.

Introduction to road paving machine hydraulic cylinder:

Before the road paving machine hydraulic cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

The wear of the hard chromium plating layer of the road paving machine hydraulic cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

The internal leakage of the road paving machine hydraulic cylinder should be prevented when the road paving machine hydraulic cylinder is used. The internal leakage of road paving machine hydraulic cylinder includes the leakage caused by excessive wear of road paving machine hydraulic cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

When the road paving machine hydraulic cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the road paving machine hydraulic cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the road paving machine hydraulic cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Answers to some questions about road paving machine hydraulic cylinder:

How to calculate the tonnage of the hydraulic press without konowing the diameter of the cylinder?
To know the tonnage of the hydraulic cylinder, you first need to know the working pressure of the hydraulic system, the inner diameter of the hydraulic cylinder and the outer diameter of the cylinder rod (the outer diameter of the cylinder rod is needed when calculating the hydraulic cylinder tension). The thrust of the hydraulic cylinder (that is, the force that the hydraulic cylinder can produce by extending out) = the cross-sectional area of the hydraulic cylinder (or the cross-sectional area of the piston) × the working pressure of the cylinder (the cross-sectional area of the piston) =pi*D^2/4= PI (take 3.14) × the square of the cross-sectional area of the piston ÷4 working pressure to see the pressure displayed on the pressure gauge when the maximum load is working.

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.